Blue PVC-A PN12.5 pipe with a gasketed bell-end.

PVC-A PN12.5 Pressure Pipe LaReTer

Manufactured by LaReTer in Italy, the PVC-A PN12.5 pressure pipe is engineered for municipal potable water transport, pressurized irrigation, and industrial fluid distribution. Combining unplasticized polyvinyl chloride with chlorinated polyethylene modifiers, this polymeric alloy eliminates brittle fracture risks while maintaining high tensile strength and structural rigidity. Supplied in 6,000 mm lengths in RAL 5015 blue, it delivers a nominal operating pressure of 12.5 bar at 20 degrees Celsius and an annular ring stiffness of SN 10 kN/m2 across nominal outside diameters from 50 mm to 500 mm.

Technical specifications

The PVC-A PN12.5 piping system provides superior hydraulic efficiency and impact tolerance under demanding operating conditions. Its ductile formulation arrests rapid crack propagation caused by surface scratches or concentrated point loads, while its smooth bore minimizes head loss and pumping energy requirements.

  • Nominal working pressure: PN 12.5 (12.5 bar at 20 degrees Celsius) with temperature derating up to 60 degrees Celsius per DIN 8061-62
  • Annular ring stiffness: SN 10 kN/m2 across all diameters from 50 mm to 500 mm
  • Hydraulic roughness coefficient: k = 0.003 mm according to Hazen-Williams flow formulas
  • Mechanical properties: Young's modulus of 2,500 MPa and yield tensile strength of at least 40 MPa per EN ISO 6259-1
  • Negative pressure tightness: certified vacuum resistance down to -0.5 bar
  • Thermal stability: Vicat softening temperature of at least 80 degrees Celsius conforming to ISO 2507

Installation and jointing

Each pipe section features an integrally thermoformed socket equipped with a factory pre-inserted Forsheda Power-Lock gasket. This jointing geometry simplifies field assembly, requires lower push-in insertion forces, and permits angular deflections up to 3 degrees to follow trench elevation changes without stressing the pipeline.

The Power-Lock sealing system integrates an elastomeric EPDM lip conforming to EN 681-1 and a co-molded yellow polypropylene retaining ring without metallic components. Mechanically locked into the socket groove during thermoforming, the gasket cannot displace, twist, or push out during pipe insertion, eliminating typical assembly defects. Additionally, the alloy allows manual cold bending during installation, and the reduced pipe weight—approximately 25 percent lighter than equivalent PE pipelines—streamlines logistical handling and trench lowering.

Materials and standards

Formulated completely without plasticizers or heavy metal stabilizers, LaReTer PVC-A material maintains full physical stability and long-term chemical inertness. The piping system is certified for direct contact with drinking water and conforms to European manufacturing and testing directives.

Quality compliance is validated by KIWA European TIC certification under mark KQ KIWA QUALITY KIP-105133 in accordance with UNI EN 1452. Health and organoleptic safety comply strictly with Italian Ministerial Decree DM 174/2004, Circular No. 102/1978, and UNI EN 1622 for neutral threshold odour and flavour numbers. The material also conforms to ISO 1183 for specific gravity (1.38 to 1.40 g/cm3), ISO 2505 for longitudinal reversion, and ISO 7686 for light opacity, ensuring an anticipated operational design life exceeding 50 years.

Manufactured by LaReTer in Italy, the PVC-A PN12.5 pressure pipe is engineered for municipal potable water transport, pressurized irrigation, and industrial fluid distribution. Combining unplasticized polyvinyl chloride with chlorinated polyethylene modifiers, this polymeric alloy eliminates brittle fracture risks while maintaining high tensile strength and structural rigidity. Supplied in 6,000 mm lengths in RAL 5015 blue, it delivers a nominal operating pressure of 12.5 bar at 20 degrees Celsius and an annular ring stiffness of SN 10 kN/m2 across nominal outside diameters from 50 mm to 500 mm.

Technical specifications

The PVC-A PN12.5 piping system provides superior hydraulic efficiency and impact tolerance under demanding operating conditions. Its ductile formulation arrests rapid crack propagation caused by surface scratches or concentrated point loads, while its smooth bore minimizes head loss and pumping energy requirements.

  • Nominal working pressure: PN 12.5 (12.5 bar at 20 degrees Celsius) with temperature derating up to 60 degrees Celsius per DIN 8061-62
  • Annular ring stiffness: SN 10 kN/m2 across all diameters from 50 mm to 500 mm
  • Hydraulic roughness coefficient: k = 0.003 mm according to Hazen-Williams flow formulas
  • Mechanical properties: Young's modulus of 2,500 MPa and yield tensile strength of at least 40 MPa per EN ISO 6259-1
  • Negative pressure tightness: certified vacuum resistance down to -0.5 bar
  • Thermal stability: Vicat softening temperature of at least 80 degrees Celsius conforming to ISO 2507

Installation and jointing

Each pipe section features an integrally thermoformed socket equipped with a factory pre-inserted Forsheda Power-Lock gasket. This jointing geometry simplifies field assembly, requires lower push-in insertion forces, and permits angular deflections up to 3 degrees to follow trench elevation changes without stressing the pipeline.

The Power-Lock sealing system integrates an elastomeric EPDM lip conforming to EN 681-1 and a co-molded yellow polypropylene retaining ring without metallic components. Mechanically locked into the socket groove during thermoforming, the gasket cannot displace, twist, or push out during pipe insertion, eliminating typical assembly defects. Additionally, the alloy allows manual cold bending during installation, and the reduced pipe weight—approximately 25 percent lighter than equivalent PE pipelines—streamlines logistical handling and trench lowering.

Materials and standards

Formulated completely without plasticizers or heavy metal stabilizers, LaReTer PVC-A material maintains full physical stability and long-term chemical inertness. The piping system is certified for direct contact with drinking water and conforms to European manufacturing and testing directives.

Quality compliance is validated by KIWA European TIC certification under mark KQ KIWA QUALITY KIP-105133 in accordance with UNI EN 1452. Health and organoleptic safety comply strictly with Italian Ministerial Decree DM 174/2004, Circular No. 102/1978, and UNI EN 1622 for neutral threshold odour and flavour numbers. The material also conforms to ISO 1183 for specific gravity (1.38 to 1.40 g/cm3), ISO 2505 for longitudinal reversion, and ISO 7686 for light opacity, ensuring an anticipated operational design life exceeding 50 years.

Variants, prices and availability
Size SKU U.M.
Price
incl. 21% VAT
Availability Add To Cart
D 50 mm
139612 m €2.76
Ships in 24 hours Ships in 7-10 days Ships in 10-15 days Max stock reached Please call
D 63 mm
139613 m €4.39
Ships in 24 hours Ships in 7-10 days Ships in 10-15 days Max stock reached Please call
D 90 mm
139614 m €8.07
Ships in 24 hours Ships in 7-10 days Ships in 10-15 days Max stock reached Please call
D 110 mm
139615 m €9.86
Ships in 24 hours Ships in 7-10 days Ships in 10-15 days Max stock reached Please call
D 125 mm
139616 m €13.13
Ships in 24 hours Ships in 7-10 days Ships in 10-15 days Max stock reached Please call
D 140 mm
139617 m €15.98
Ships in 24 hours Ships in 7-10 days Ships in 10-15 days Max stock reached Please call
D 160 mm
139618 m €20.93
Ships in 24 hours Ships in 7-10 days Ships in 10-15 days Max stock reached Please call
D 200 mm
139619 m €32.59
Ships in 24 hours Ships in 7-10 days Ships in 10-15 days Max stock reached Please call
D 225 mm
139620 m €41.13
Ships in 24 hours Ships in 7-10 days Ships in 10-15 days Max stock reached Please call
D 250 mm
139621 m €50.34
Ships in 24 hours Ships in 7-10 days Ships in 10-15 days Max stock reached Please call
D 280 mm
139622 m €67.30
Ships in 24 hours Ships in 7-10 days Ships in 10-15 days Max stock reached Please call
D 315 mm
139623 m €79.48
Ships in 24 hours Ships in 7-10 days Ships in 10-15 days Max stock reached Please call
D 355 mm
139624 m €112.47
Ships in 24 hours Ships in 7-10 days Ships in 10-15 days Max stock reached Please call
D 400 mm
139625 m €136.09
Ships in 24 hours Ships in 7-10 days Ships in 10-15 days Max stock reached Please call
D 500 mm
139626 m €213.63
Ships in 24 hours Ships in 7-10 days Ships in 10-15 days Max stock reached Please call
incl. 21% VAT
SKU: 139612
D: 50 mm
Ships in 24 hours
€2.76 / m
SKU: 139613
D: 63 mm
Ships in 24 hours
€4.39 / m
SKU: 139614
D: 90 mm
Ships in 24 hours
€8.07 / m
SKU: 139615
D: 110 mm
Ships in 24 hours
€9.86 / m
SKU: 139616
D: 125 mm
Ships in 24 hours
€13.13 / m
SKU: 139617
D: 140 mm
Ships in 24 hours
€15.98 / m
SKU: 139618
D: 160 mm
Ships in 24 hours
€20.93 / m
SKU: 139619
D: 200 mm
Ships in 24 hours
€32.59 / m
SKU: 139620
D: 225 mm
Ships in 24 hours
€41.13 / m
SKU: 139621
D: 250 mm
Ships in 24 hours
€50.34 / m
SKU: 139622
D: 280 mm
Ships in 24 hours
€67.30 / m
SKU: 139623
D: 315 mm
Ships in 24 hours
€79.48 / m
SKU: 139624
D: 355 mm
Ships in 24 hours
€112.47 / m
SKU: 139625
D: 400 mm
Ships in 24 hours
€136.09 / m
SKU: 139626
D: 500 mm
Ships in 24 hours
€213.63 / m